Washing machine What does the error code means and how to fix it?New CodeOld CodeCauseSolution1EE7Water level sensor Issue. Switch off the appliance at the mains then wait 30 seconds. Switch appliance back on again and start a new programme.3E3E13E23E33E4EAEBMotor defect. Switch off the appliance at the mains then wait 30 seconds. Switch appliance back on again and start a new programme.E4E1Water supply error. The appliance is not detecting that the unit is filling with water. Check water supply is turned on and that there is adequate water pressure (min:0.5bar, max: 8bar).
![Beko Beko](/uploads/1/2/5/3/125370322/577886706.jpg)
Check to see if the water hoses are not kinked. Check Inlet filters inside end of Water Valve. If water supply is OK,4E14E24EdWater temperature issue. Check water hose is connected to a cold supply and not a hot supply.
Cold water is usually indicated by a blue tap.5EE2Water drainage issue. Water is not draining from appliance. Check drainage pump filter for blockages (e.g. Lint, coins hair, clips). Check drain hose and waste connection for kinks and blockages.Then select a spin cycle to drain the remaining water in the appliance.6E. Over current error.
Switch off the appliance at the mains then wait 30 seconds. Switch appliance back on again and start a new programme.9E1PH1Power error. Switch off the appliance at the mains then wait 30 seconds. Switch appliance back on again and start a new programme.9E2PloPower error.
Dishwasher repairs by official Beko engineers across the UK. Call today for appointments within 48 hours and all repairs guaranteed! Get the Beko dishwasher spares you need to repair your Beko dishwasher. To find your product code, model and serial number, open the door and the rating plate is located on the right hand edge of the door.
Switch off the appliance at the mains then wait 30 seconds. Switch appliance back on again and start a new programme.AE13ESignal communication error between Main PCB and Sub PCB. Switch off the appliance at the mains then wait 30 seconds. Switch appliance back on again and start a new programme.bE. Motor issue. Switch off the appliance at the mains then wait 30 seconds.
Switch appliance back on again and start a new programme.bE112EPower button issue. Button held in too long. Check whether any of the buttons are sticking or are stuck in. Disconnect appliance from mains and clean the buttons with a lightly dampened cloth.B2/bE214EControl button issue. Button held in too long. Check whether any of the buttons are sticking or are stuck in.
Disconnect appliance from mains and clean the buttons with a lightly dampened cloth.bE318EButton defective. Please call the customer support team.CEE8Water cool down issue.
Check water hose is connected to a cold supply and not a hot supply. Cold water is usually indicated by a blue tap.dEdE1EdDoor issue. Check that the door is closed fully. Check nothing is trapping in the door.
Check unit is not overloaded.dE2. Appliance too hot. This is not a fault; appliance fan will continue to run until the appliance is cool enough for the washing to be removed (55°C).
Then the door will unlock. – This prevents heater faults.LELE1E911ENatural drain/Water leak - Low water level detected during cycle. Check that the level of the drain hose is not lower than the base of the washing machine. Additionally check for a water leak. If no trace of water, switch off the power, reconnect and try again.OEOFE3Overflow error. Too much washing powder/liquid may have been added. Switch off the power to the appliance, wait 30 seconds then Switch the power supply back on.
The drain pump should operate to drain the washing machine.t1ee2/t2tSt. This occurs when too much foam is detected and is displayed whilst foaming is being removed.
This is not a fault. The appliance will usually cure this fault on its own, however if it does not you will need to run either an 'Eco drum clean' cycle (some models) or a 90°C cotton cycle with no detergent or washing load.
To prevent this from happening please reduce the quantity of detergent used.tEECTemperature sensor issue. Switch off the appliance at the mains then wait 30 seconds. Switch appliance back on again and start a new programme.tE1tE2tE3. Excessive fluctuation in the supply voltage.
Switch off the appliance at the mains then wait 30 seconds. Switch appliance back on again and start a new programme.UEE4Unbalanced error - The load in the drum is unbalanced. This is not a fault. The appliance is detecting an unbalanced load and is stopping the spin for safety reasons.
To help prevent this from occurring please redistribute washing by adding or removing items to ensure a more balance load. Single large/heavy items such as bath mats or large towels are unlikely to spin on their own so please add 2/3 additional towels and put on another spin cycle.